www.U-LineService.comPhone (414) 354-0300 • FAX (414) 354-7905Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696OnlineService@U-
CLR2060 — Clear Ice Makerwww.U-LineService.com 10 02/2005™ 4. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon s
CLR2060 — Clear Ice Maker02/2005 11 www.U-LineService.com™3. Install the pivot post into the new Replacement Bottom Hinge (using the 7/64" hex ke
CLR2060 — Clear Ice Makerwww.U-LineService.com 12 02/2005™3. See Figure 28. If the top far edge of the door needs to move UP, move the hinge plate tow
CLR2060 — Clear Ice Maker02/2005 13 www.U-LineService.com™If using a Gravity Drain:1. Attach the 5/8-inch ID drain connection on the back of the unit
CLR2060 — Clear Ice Makerwww.U-LineService.com 14 02/2005™To check and test hose connections:1. Make certain the unit is not plugged into an electrica
CLR2060 — Clear Ice Maker02/2005 15 www.U-LineService.com™CAUTIONIn the event of a power outage, restricted drain or pump failure, the failure to use
CLR2060 — Clear Ice Makerwww.U-LineService.com 16 02/2005™Electrical SpecificationsCAUTIONElectrical installation must observe all state and local cod
CLR2060 — Clear Ice Maker02/2005 17 www.U-LineService.com™2. If the ice maker is not level, adjust the feet on the corners of the unit as necessary (s
CLR2060 — Clear Ice Makerwww.U-LineService.com 18 02/2005™Installation TroubleshootingProblemQ:Water is leaking under the unit.SolutionA:A water leak
CLR2060 — Clear Ice Maker02/2005 19 www.U-LineService.com™4. Watch the water flow over the evaporator assembly (ice cube tray) to familiarize yourself
CLR2060 — Clear Ice Makerwww.U-LineService.com 2 02/2005™ContentsCut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Product
™©2005 U-Line CorporationPublication No. 30051E02/2005U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in unde
CLR2060 — Clear Ice Maker02/2005 3 www.U-LineService.com™General PrecautionsUse this appliance for its intended purpose only and follow these general
CLR2060 — Clear Ice Makerwww.U-LineService.com 4 02/2005™Your U-Line product has been designed for either free-standing or built-in installation. When
CLR2060 — Clear Ice Maker02/2005 5 www.U-LineService.com™Reversing the Door(Black and White Units Only)All U-Line units (except Stainless Steel models
CLR2060 — Clear Ice Makerwww.U-LineService.com 6 02/2005™Other Site RequirementsPower SupplyThe unit requires a grounded and polarized 115 VAC, 60 Hz,
CLR2060 — Clear Ice Maker02/2005 7 www.U-LineService.com™(Black and White Units Only)Two types of custom door panels can be installed on your Black or
CLR2060 — Clear Ice Makerwww.U-LineService.com 8 02/2005™Full Overlay Door PanelDoor Panel PreparationA full overlay door panel completely covers the
CLR2060 — Clear Ice Maker02/2005 9 www.U-LineService.com™4. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View).0.177" diame
Commentaires sur ces manuels