ICE-MAKERS, COMBOS ANDREFRIGERATORS User’User’s Manuals Manual
8. Allow at least 1-1/2 inches clearance behind the unit for electri-cal and water supply connections.LEVELING THE UNITIt is important that the unit,
Figure 104. Place the two hook-hinges (located on the rear bottom side of thegrill) on the front lip of the unit base. Swing the grill up into posi-t
GLASS SHELF INSTALLATION (FOR MODELS WITH GLASS SHELVES)1. Carefully remove the shelves from inside the unit and remove thepackaging.2. Slide the shel
REVERSING THE DOORDepending upon the location of the unit, it may be desirable to changethe side on which the door is mounted.NOTEOn Combo Models 29A
6. Relocate plastic spacer/bushing on bottom of door to oppositeside, and place door on bottom hinge pin (see Figure 18). Cleanout bushing hole in do
11. Fasten upper hinge to unit (3screws). Partially tightenscrews until door is aligned.See Figure 21.9. Remove three plastic plugsin hinge holes, top
12. Adjust door to assure proper seal. Tighten upper hinge screwssecurely.13. Replace three plastic plugs removed in step 8 into holes on top ofunit.
8. Install bottom hinge on cabi-net, opposite side, aligningflat edge of hinge with outeredge of unit. Partially tightenscrews until door is aligned.
NOTEWhen inspecting door align-ment, make sure that thelight switch bracket (whereequipped) makes contactwith the light switch plunger(see Figure 24).
Install the insert as follows:Insert edges may be SHARP! Use care when installing.1. Remove top hinge screw pin (large Phillips head, see Figure 25).
U-LINE CORPORATION LIMITED WARRANTYU-Line Corporation warrants each U-Line product to be free from defects in materials andworkmanship for a period of
NOTEUse care not to bend light switch bracket (where installed),located on door bottom when installing door insert. Do notset door on bottom edge when
19HDWUL118CABINET OR WALLUL126AT LEAST 1" CLEARANCE REQUIRED IFUNIT IS INSTALLED FLUSH WITHCABINET OR WALL.1.000CABINETOR WALLUL125AT LEAST 9&quo
INITIAL START-UPOnce installation is complete, the unit is ready for initial start-up andoperation.NOTEModels SP18, BI-15, BI-95,BI-98, Combo 29A, Com
4. Model 29AD only - The auto-matic defrost timer, locatedbehind the front grill, mustbe set whenever the refrig-erator is put into operation.To set
NORMAL OPERATIONOn units with refrigerator sections, the unit has been designed toachieve a fresh food temperature of approximately 38°F. Those unitsw
If ice maker is not used regularly, the ice bucket should be emptied peri-odically to ensure fresh cubes.It is normal for cubes to appear cloudy. This
ADJUSTING ICE CUBE SIZEOn models equipped with an ice maker, the cube size may be adjustedby changing the amount of water injected into the ice maker
CARE AND CLEANINGPeriodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. We suggest the following:• The inter
DEFROSTINGDO NOT use any type of electrical heating device, ice pick,knife, or other sharp instrument to defrost, as this coulddamage the inner lining
8. Leave water supply line and power cord disconnected until readyto reuse.NOTEThe use of anti-freeze or other products of this nature is notnecessar
INTRODUCTIONCongratulations on your purchase of U-Line ice making or refrigerationproducts. A pioneer in the field for more than 30 years, U-Line is t
Problem Possible Cause RemedyThe unit is not For model 29AD only:cold enough is the defrost timer set (continued) to the correct time of day?See INITI
29IF SERVICE IS REQUIREDIf the need for service arises, contact the dealer from whom the unitwas purchased. State the Model Number and Serial Number a
RRRCP.O. Box 245040Milwaukee, WI 53224-9540Phone 414.354.0300FAX 414.354.7905Printed in U.S.A.P/N 41923
TABLE OF CONTENTSINTRODUCTION...1SAFETY PRECAUTIONS ...
Warning means that failure to follow this safety statementmay result in extensive product damage, serious personalinjury, or death.Caution means that
4User’s Manual• Using a heater to speed up defrosting can cause per-sonal injury and damage to the inner lining. DO NOT useany type of electrical heat
5NOTE Keep in mind that the door ofthe unit may be mounted oneither side of the cabinet (seeREVERSING THE DOOR). AllU-Line units have a zero clear-anc
CONNECTING THE WATER SUPPLY6User’s ManualUL101POWERCORDWATER LINE3. Carefully bend the water sup-ply line into position and con-nect the line to the
4. For recessed installations,allow extra water supply linelength to provide slack for easyremoval from the recessedarea (see Figure 7). This willalso
Commentaires sur ces manuels